System Indicator
NOTE:
If the system is OK, the SRS indicator should come on when you turn the vehicle to the ON mode, and turns off 6 seconds later. If it does not, there is a problem with the system.
If the SRS indicator comes on, and SRS DTCs are not indicated, do the SRS symptom troubleshooting.
How to Read DTCs with the Scanner
How to Troubleshoot Circuits at the Connectors Especially for Connectors with Terminal Test Ports
Special Tools Required
Male Pin Probe 07ZAJ-RDJA110
NOTE:
Make sure the 12 volt battery is fully charged when doing an electrical test. If the 12 volt battery is not fully charged, the results of the tests may not be accurate.
To prevent damage to the connector terminals, do not insert test equipment probes, paper clips, or other substitutes. Damaged terminals cause a poor connection and an incorrect measurement.
- When diagnosing or troubleshooting the circuits at the connectors (A), use the appropriate terminal test port as shown. Gently insert the pin probe of the tester or jumper wire at the terminal test port from the terminal side.
- Connect one side of the patch cord terminals (A) to a commercially available digital multimeter (B), and connect the other side of the terminals (C) to the male pin probe.
- Gently contact the male pin probe at the terminal test port from the terminal side. Do not force the tips into the terminals.
Do not insert the pin probes of the tester or a jumper wire at the terminal or the SRS short canceller terminal port.
To prevent damage to the connector terminals, do not insert the test equipment probes, paper clips, or other substitutes as they can damage the terminals. Damaged terminals cause a poor connection and an incorrect measurement.
For accurate results, always use the male pin probe.
To prevent damage to the connector terminals, do not insert test equipment probes, paper clips, or other substitutes. Damaged terminals cause a poor connection and an incorrect measurement.
Do not puncture the insulation on a wire. Punctures can cause poor or intermittent electrical connections.
How to Troubleshoot Circuits at the Connectors Except for Connectors with Terminal Test Ports
When using electrical test equipment, insert the probe of the tester into the wire side of the connector (except for connectors with terminal test ports).
NOTE:
- Make sure the 12 volt battery is fully charged when doing an electrical test. If the 12 volt battery is not fully charged, the results of the tests may not be accurate.
- Do not insert the probe of the tester into the terminal side of the connector, and do not tamper with the connector.
- To prevent damage to the connector, do not insert test equipment probes, paper clips, or other substitutes. Damaged terminals cause a poor connection and an incorrect measurement.
- Do not puncture the insulation on a wire. Punctures can cause poor or intermittent electrical connections.
- Use specified service connectors in troubleshooting. Using improper tools could cause a diagnostic error due to poor metal-to-metal contact.
- Use a U-shaped probe. Do not insert the probe forcibly.
Special Tools Required
NOTE:
- To prevent damage to the connector cavity, insert an SRS short canceller straight into the cavity from the terminal side.
- Before installing an SRS short canceller, wash it with electrical contact cleaner, then dry it with compressed air.
- Do not use an SRS short canceller if it is damaged.
- Make sure to remove an SRS short canceller before reconnecting the SRS unit connector.
- Some systems store data in memory that is lost when the 12 volt battery is disconnected. 12 Volt Battery Terminal Disconnection and Reconnection.
DTC (Diagnostic Trouble Codes)
- The self-diagnostic function of the SRS unit allows it to locate the causes of system problems and store this information in memory. For easier troubleshooting, this data can be retrieved with the scanner via the data link circuit.
- When you turn the vehicle to the ON mode, the SRS indicator should come on. If it goes off after 6 seconds, the system is normal and is not currently detecting any problems.
- If there is a problem, the system locates and defines the problem, stores this information in the memory, and turns on the SRS indicator. The data remains in the memory even if the vehicle is turned to the OFF (LOCK) mode or the 12 volt battery is disconnected.
- The data is stored in memory as a diagnostic trouble code (DTC).
- DTCs are either latching or resetting depending on the malfunction. With resetting DTCs, the SRS indicator goes off the next time the vehicle is turned to the ON mode, and the system is normal, but the DTC is still stored. With latching DTCs, the SRS indicator does not turn off until the malfunction is repaired and the DTC is cleared.
- When you connect the scanner to the data link connector (DLC), you can retrieve a more detailed DTC in the scanner ''SRS'' menu.
- After reading and recording the DTC, go to the troubleshooting procedure for that code.
- Make sure the 12 volt battery is fully charged. If the 12 volt battery is dead or low, electrical measurement values may not be correct.
- Use only a digital multimeter to check the system. Make sure its output is 10 mA (0.01 A) or less when switched to the smallest value in the ohmmeter range. A tester with a higher output could damage the airbag circuit or cause accidental airbag deployment and possible injury.
- Whenever the vehicle is turned to the ON mode, or the vehicle is in the OFF (LOCK) mode for less than 3 minutes, be careful not to bump the SRS unit; the system could falsely interpret an impact or rollover, deploying airbags in response and cause damage or injuries.
- Before removing the dashboard wire harness, floor wire harness disconnect the driver's airbag inflator connector, the front passenger's airbag inflator connector, both side airbag inflator connectors, both side curtain airbag inflator connectors, and both front seat belt tensioner connectors.